TKSA11-MBH_MANYETİK ÇUBUK TUTUCU SKF

TKSA11-MBH_MANYETİK ÇUBUK TUTUCU SKF
Kategori
Lazerli Eksen Ayar Cihazları
Marka
SKF
Stok Kodu
SKF.TKSA11-MBH
Ürün Bilgisi
Ürün Bilgisi
SKF Shaft Alignment Tool TKSA 11Quick Start Guide1. Description183426751. Measuring unit5. Two inductive proximity sensors2. Power button6. V-Bracket with locking chain3. Connection blue LED7. Magnetic bar holder4. Status red/green LED8. Reference bar
2SKF TKSA 112. Compatible display devices! SKF TKSA DISPLAY2, Samsung Galaxy Tab Active 2 and iPad Mini recommended! iPad, iPod Touch, iPhone SE, Galaxy S6 or above (all not included) 3. Installing the app Note: Alignment apps are pre-installed and ready to use on the SKF TKSA DISPLAY2 device.1. Turn on Wi-Fi and connect to an internet network 2. Tap the App Store icon (iOS) or Google Play Store icon (Android) 3. Tap the search area4. Enter “SKF TKSA 11”5. Select the app you want to install6. Tap “GET” (iOS only) and then “INSTALL”
3SKF TKSA 114. Supporta. Instructions for use Complete instructions for use for the apps and the hardware can be found in:Help section of the appsand SKF.com/Alignmentb. Technical supportSKF Technical Support website link is available in the help section the apps. Please visit www.skf.com/cm/tsg to find help or file a support request.c. VideosShort instructional videos are available in the help section of the apps. More videos can be found on SKF Maintenance Products YouTube page: www.mapro.skf.com/youtube
4SKF TKSA 115. Mounting the measuring unitMount the Measuring unit on the Moveable machine (Motor) side.Adjust the gap between the inductive proximity sensors and the reference bar to app. 3 mm ±0,5 mm (120 mils ±20 mils). “Sensor status” in the app indicates the correct distance.The TKSA 11 can be mounted directly on couplings when needed.
5SKF TKSA 11Safety recommendations! The complete instructions for use are available on SKF.com and within the SKF TKSA 11 app.! Read and follow all warnings in this document before handling and operating the equipment. You can be seriously injured, equipment and data can be damaged if you do not follow the safety warnings.! Always read and follow the operating instructions.! The equipment should not be used in areas where there is a risk for explosion.! Do not expose the device to extreme heat.! Do not charge the Measuring units below +4 °C (+40 °F) or above +45 °C (+113 °F).! Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts.! Do not overreach. Keep proper footing and balance at all times to enable better control of the device during unexpected situations.! Use safety equipment. Non-skid safety shoes, hard hat or hearing protection must be used for appropriate conditions.! Never work on energized equipment unless authorized by a responsible authority. Always turn off the power of the machine before you start.! Do not expose the equipment to rough handling or impacts this will void the warranty.! Avoid direct contact with water, wet surfaces, or condensing humidity.! Do not attempt to open the device.! Use only accessories that are recommended by SKF.! Device service must be performed only by qualified SKF repair personnel.! We recommend calibrating the tool every 2 years.Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. Android, Google Play and the Google Play logo are trademarks of Google Inc.
SKF Maintenance Products® SKF is a registered trademark of the SKF Group. © SKF Group 2018/08www.mapro.skf.com ! www.skf.com/mount ! MP5432ENThe contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of use of the information contained herein.EU Declaration of conformityWe, SKF Maintenance Products Kelvinbaan 16 3439 MT Nieuwegein The Netherlandsherewith declare that the following product:SKF Shaft Alignment Tool TKSA 11has been designed and manufactured in accordance with:RADIO EQUIPMENT DIRECTIVE 2014/53/EU as outlined in the harmonized norm EN 61010:2010, EN 61326-1:2013 Class B, group 1 equipmentIEC 61000-4-2:2009, IEC 61000-4-3:2006EN 301 489-1 v2.1.1, EN 301 489-17 v3.1.1, EN 300 328 v2.1.1EUROPEAN ROHS DIRECTIVE 2011/65/EUThe enclosed device complies with Part 15 of the FCC Rules. Contains FCC ID: QOQBLE112Certification Number: IC: 5123A-BGTBLE112Manufacturer’s Name, Trade Name or Brand Name: bluegigaModel Name: BLE112-ANieuwegein, The Netherlands, August 2017Sébastien DavidManager Product Development and Quality
Yorumlar
Bu ürüne ilk yorumu siz yapın!
Yorum Yaz
Taksit Seçenekleri
Önerileriniz
Bu ürünün fiyat bilgisi, resim, ürün açıklamalarında ve diğer konularda yetersiz gördüğünüz noktaları öneri formunu kullanarak tarafımıza iletebilirsiniz.
Görüş ve önerileriniz için teşekkür ederiz.
TKSA11-MBH_MANYETİK ÇUBUK TUTUCU SKF SKF.TKSA11-MBH
TKSA11-MBH_MANYETİK ÇUBUK TUTUCU SKF

Tavsiye Et

*
*
*
IdeaSoft® | E-Ticaret paketleri ile hazırlanmıştır.