TMFT 36 İÇİN DARBE HALKASI, BOYUT A15-35 SKF

TMFT 36 İÇİN DARBE HALKASI, BOYUT A15-35 SKF
Kategori
Mekanik Aletler
Marka
SKF
Stok Kodu
SKF.TMFT36A15-35
Ürün Bilgisi
Ürün Bilgisi
Helps prevent premature bearing failures SKF Bearing fitting tool kit TMFT 36Poor fitting, usually using brute force, accounts for 16% of premature bearing failures. The SKF Bearing fitting tool kit is designed for quick and precise mounting of bearings, while minimising the risk of bearing damage. The right combination of impact ring and sleeve allows effective transmission of mounting force to the bearing ring with the interference fit, minimising the risk of damaging the bearing’s raceways or rolling elements. In addition to mounting bearings, the TMFT 36 is also suitable for mounting other components such as bushings, seals and pulleys. The kit contains 36 impact rings, 3 impact sleeves and a dead-blow hammer packed in a lightweight carrying case.! The TMFT 36 facilitates the mounting of different bearings with bore diameters from 10–55 mm! Facilitates correct mounting on shaft, housing and blind applications! The diameter of the impact ring precisely fits the inner and outer diameter of the bearing! Small diameter of the impact area on top of the sleeve allows effective transmission and distribution of mounting force ! Impact rings and sleeves are made of high impact resistant material for longevity! Click connection between impact ring and sleeve provides stability and durability! The impact rings are suitable for use under a press! Impact rings are marked for clear visual identification of the ring’s size and easy selection! Even surface of the impact sleeve’s body provides excellent grip! The nylon double-side head of the dead-blow hammer helps to prevent damaging the components! The rubber handgrip of the dead-blow hammer provides excellent gripDesignationTMFT 36Impact ringsBore diameter Outer diameter 10–55 mm (0.39–2.17 in.)26–120 mm (1.02–4.72 in.)SleevesMaximum shaft length Sleeve A: 220 mm (8.7 in.) Sleeve B: 220 mm (8.7 in.) Sleeve C: 225 mm (8.9 in.)HammerTMFT 36-H, weight 0,9 kg (2.0 lb)Carrying case dimensions530 × 110 × 360 mm (20.9 × 4.3 × 14.2 in.)Number of rings36Number of sleeves3Weight (including carrying case) 4,4 kg (9.7 lb)Technical data
skf.com | skf.com/mapro | skf.com/lubrication® SKF is a registered trademark of the SKF Group. © SKF Group The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.PUB MP/P8 1 07 / EN · October Interference fits on cylindrical shaftsMost bearings are fitted to their shaft or housing with one component having an interference fit. For determining the correct fit, refer to the SKF General Catalogue, the SKF Maintenance Handbook or consult an SKF application engineer.Incorrect mountingWhen bearings are mounted cold, care must be taken to ensure the drive-up forces are applied to the ring with the interference fit. Damage to the bearing resulting in a failure can occur if the mounting force is transmitted through the rolling elements causing damage to the raceways.Correct mountingThe correct way to minimise raceway damage is to use specifically designed tools from SKF, such as the Bearing fitting tool kits and Combi kits. These tools allow drive-up forces to be applied effectively and evenly to the component with the interference fit, avoiding raceway damage.Shaft interference fitHousing interference fitUneven distribution of forces can result in raceway damageWith the correct tools, raceway damage is avoidedDGBBDGBB (sealed)SABBSRACBBDRACBBSRBCRBTRBCARB6 – 6 116 – 6 111 – 1 117 – 7 113 – 3 11 13 5 – 1311N 1 5 – N 1 113 3 – 3 11C 5 – C 116 – 6 116 3 – 6 3111 97 – 7 1133 – 3311 5/ N – N 113 3 – 3 311C 4 1 63 – 631163 – 63 1 13 1 – 131173 1 – 7311 5 – 11N 3 – N 11313 5 – 31311C 6 664 3 – 64 9 – 11 3 8 – 311N 3 4 – N 3113 4 – 3 116 9 3 1 – 311N 3 4 – N 3 113 5 – 3 116 / 11 7 – 11 1 N 3 3 – N 3113 3 3 – 3 3116 / 833 1 – 33 1163/ 33 5 – 33 1163/ 816 – 16 11161 – 161 198 3 – 98 6TMFT 6 is suitable for SKF bearing series
Yorumlar
Bu ürüne ilk yorumu siz yapın!
Yorum Yaz
Taksit Seçenekleri
Önerileriniz
Bu ürünün fiyat bilgisi, resim, ürün açıklamalarında ve diğer konularda yetersiz gördüğünüz noktaları öneri formunu kullanarak tarafımıza iletebilirsiniz.
Görüş ve önerileriniz için teşekkür ederiz.
TMFT 36 İÇİN DARBE HALKASI, BOYUT A15-35 SKF SKF.TMFT36A15-35
TMFT 36 İÇİN DARBE HALKASI, BOYUT A15-35 SKF

Tavsiye Et

*
*
*
IdeaSoft® | E-Ticaret paketleri ile hazırlanmıştır.