TMHP 10E VE TMHC 110E İÇİN CIVATA VE SOMUNLU KOL S

TMHP 10E VE TMHC 110E İÇİN CIVATA VE SOMUNLU KOL S
Kategori
Mekanik Aletler
Marka
SKF
Stok Kodu
SKF.TMHP10E-5
Ürün Bilgisi
Ürün Bilgisi
SKF Hydraulic & Strong Back Pullers
SKF Hydraulic Jaw Puller! A versatile kit with three different arm lengths is suitable for a wide range of applications! Hydraulic spindle facilitates effortless dismounting! Self-locking arms minimise the risk of the puller slipping from the application when under load! The spring-loaded centre point of the hydraulic spindle allows easy puller centring ! The hydraulic spindle is equipped with a safety valve, which minimises the risk of puller overload! High load rating of 100 kN (11.2 US ton) makes the puller suitable for a variety of dismounting jobs! A hydraulic spindle stroke of 80 mm (3.1 in.) helps facilitate dismounting in one operation! Supplied with hydraulic spindle extension pieces to allow quick adaptation to pulling lengthEffortless bearing dismounting up to 100 kN SKF Hydraulic Jaw Puller Kit TMHP 10ETechnical data DesignationTMHP 10EContents1 × arm–assembly stand3 × arms, 115 mm (4.5 in.)3 × arms, 160 mm (6.3 in.)3 × arms, 00 mm (7.8 in.)1 × hydraulic spindle TMHS 1003 × extension pieces for hydraulic spindle; 50, 100 and 150 mm (2, 4, 6 in.)1 × nosepiece with centre pointfor hydraulic spindleMaximum stroke80 mm (3.1 in.)Nominal working force100 kN (11.2 US ton)Threading hydraulic cylinder1 1/2'-16 tpiCarrying case dimensions578 × 410 × 70 mm (23 × 16 × 2.8 in.)Weight14,5 kg (32 lb)Arms set 2 (3 ×)Effective arms lengthWidth of gripClaw height 115 mm 75–170 mm 8 mm (4.5 in.) (2.9–6.7 in.)(0.3 in.)Arms set 2 (3 ×)Effective arms lengthWidth of gripClaw height 160 mm 80– 50 mm 8 mm (6.3 in.) (3.1–9.8 in.)(0.3 in.)Arms set 3 (3 ×)Effective arms lengthWidth of gripClaw height 00 mm 110– 80 mm 8 mm (7.9 in.) (4.3–11 in.)(0.3 in.)
Easy bearing dismounting even in the tightest spacesSKF Strong Back Pullers TMBS E seriesThe SKF TMBS E strong back pullers facilitate dismounting of bearings in applications where the use of traditional jaw pullers is restricted due to lack of space or where the application demands a long reach.! Special separator design allows the puller to be easily inserted between the bearing and the shoulder on the shaft! The spring-loaded centre point of the hydraulic spindle allows easy puller centring! The firm grip behind the bearing’s inner ring reduces the force required to dismount the bearing! The hydraulic spindle is equipped with a safety valve, which minimises the risk of puller overload! A hydraulic spindle stroke of 80 mm (3.1 in.) helps facilitate dismounting in one operationPowerful combination of a jaw and strong back pullerSKF Hydraulic Puller Kit TMHC 110ESKF Strong Back Pullers! SKF TMBS 50E is equipped with a mechanical spindle for force generation! SKF TMBS 100E and the SKF TMBS 150E are equipped with a hydraulic spindle, which allows for easy application of force up to 100 kN (11.2 US ton) ! Supplied with hydraulic spindle extension pieces to allow quick adaptation to pulling length! SKF TMBS 100E and SKF TMBS 150E are supplied with extension rods to allow quick adaptation to pulling lengths upto 816 mm (32.1 in.)! SKF TMHC 110E hydraulic puller kit combines a jaw puller and a strong back puller ! A versatile puller kit facilitates safe and easy dismounting in a variety of applications! Hydraulic spindle facilitates easy and quick dismounting! High load rating of 100 kN (11.2 US ton)! The strong back puller includes two different arm lengths for maximum reach of 115 mm (4.5 in.)! The jaw puller can be assembled as a three-arm or two-arm puller depending on the space and demands of the application! The firm grip of the strong back puller behind the bearing’s inner ring reduces the force required to dismount the bearing! Supplied with extension rods to allow quick adaptation to pulling lengths upto 245 mm (9.6 in.)DesignationShaft diameterMaximum bearing outer diameterMaximum reachmmin.mmin.mmin.TMBS 50E7–500.3–1.9853.31104.3TMBS 100E20–1000.8–3.91606.3120–8164.7–32.1TMBS 150E 5–1501.4–5.92158.5120–8164.7–32.1TMHC 110E20–1000.8–3.91606.3120–2454.7–9.6Selection chart
skf.com | skf.com/mapro | skf.com/mount® SKF is a registered trademark of the SKF Group. © SKF Group The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.PUB MP/P8 3 78/2 EN · May Technical data DesignationTMHC EContents × arm–assembly stand3 × arms, 65 mm (2.6 in.)3 × arms, 5 mm (4.5 in.) × separator set × beam × main rods × extension rods, 5 mm (4.9 in.) × hydraulic spindle TMHS × extension pieces for hydraulic spindle; 5 , mm (2.0, 3.9 in.) × nosepiece with centre pointfor hydraulic spindleMaximum stroke8 mm (3.1 in.)Nominal working force kN (11.2 US ton)Threading hydraulic cylinder 1/2'- 6 UNCarrying case dimensions58 × 4 × 7 mm (23 × 16 × 2.8 in.)Weight 3,5 kg (29.8 lb)Arms set 1 (3 ×)Effective arms lengthWidth of gripClaw height 65 mm 5 – mm 8 mm (2.5 in.) (2–4.3 in.)(0.3 in.)Arms set 2 (3 ×)Effective arms lengthWidth of gripClaw height 5 mm 75– 7 mm 8 mm (4.5 in.) (2.9–6.7 in.)(0.3 in.)Strong back pullerMaximum reachShaft diameter range 5 mm – mm (9.8 in.) (0.8–3.9 in.)Technical data DesignationTMBS 5 ETMBS ETMBS 5 EContents × separator set × mechanical spindle × beam × main rods × separator set × main rods × extension rods, 5 mm (4.9 in.)4 × extension rods, 85 mm (11.2 in.) × beam × hydraulic spindle TMHS × extension pieces for hydraulic spindle; 5 , mm (2.0, 3.9 in.) × nosepiece with centre point for hydraulic spindle × separator set × main rods × extension rods, 5 mm (4.9 in.)4 × extension rods, 85 mm (11.2 in.) × beam × hydraulic spindle TMHS × extension pieces for hydraulic spindle; 5 , mm (2.0, 3.9 in.) × nosepiece with centre point for hydraulic spindleMaximum stroke–8 mm (3.1 in.)8 mm (3.1 in.)Nominal working force3 kN (3.4 US ton) kN (11.2 US ton) kN (11.2 US ton)Maximum reach mm (4.3 in.) –8 6 mm (4.7–32.1 in.) –8 6 mm (4.7–32.1 in.)Shaft diameter range7–5 mm (0.3–2 in.) – mm (0.8–3.9 in.)35– 5 mm (1.4–5.9 in.)Threading hydraulic cylinder– 1/2'- 6 UN 1/2'- 6 UNCarrying case dimensions 95 × 9 × 5 mm (11.6 × 7.5 × 2 in.)58 × 4 × 7 mm (23 × 16 × 2.8 in.)58 × 4 × 7 mm (23 × 16 × 2.8 in.)Weight ,8 kg (4 lb) 3,5 kg (29.8 lb) 7 kg (37.5 lb)
Yorumlar
Bu ürüne ilk yorumu siz yapın!
Yorum Yaz
Taksit Seçenekleri
Önerileriniz
Bu ürünün fiyat bilgisi, resim, ürün açıklamalarında ve diğer konularda yetersiz gördüğünüz noktaları öneri formunu kullanarak tarafımıza iletebilirsiniz.
Görüş ve önerileriniz için teşekkür ederiz.
TMHP 10E VE TMHC 110E İÇİN CIVATA VE SOMUNLU KOL S SKF.TMHP10E-5
TMHP 10E VE TMHC 110E İÇİN CIVATA VE SOMUNLU KOL S

Tavsiye Et

*
*
*
IdeaSoft® | E-Ticaret paketleri ile hazırlanmıştır.